Reliable Kitchen Remodeling Plumbing in Worth, IL
Whether you need a quick faucet swap or a complex kitchen plumbing overhaul, we’ve got you covered. From hooking up your new disposal and dishwasher to relocating sinks or adding gas lines for cooktops, we tailor the work to fit your project’s size and scope. Depending on the job, permits may be needed, and we take care of that too.
My recommendation: bring your plumber onto the project before cabinets are installed. For example, if you’re moving the sink, the drain rerouting has to happen while the floor is open. Gas line installations for new ranges or islands must be roughed in early. Pot fillers require wall access behind your stove, so it’s far easier to install before backsplash tile goes on. Getting plumbing scheduled early prevents costly hold-ups down the line.
We also offer standalone kitchen plumbing services for existing setups — faucet replacements, garbage disposal repairs, dishwasher hookups, refrigerator water line installs, and more. If you’re remodeling, it’s a wise time to check your water heater’s capacity and clear any slow drains before cabinets go back. Give us a call at 708-734-6594 to discuss.
Our Kitchen Plumbing Services
Kitchen Sink & Faucet Installation
We install all styles of kitchen sinks: undermounts needing precise countertop cuts, drop-in models, farmhouse/apron-front styles, as well as single, double, and prep sinks. Our work includes fitting the drain basket, strainer, and P-trap, plus connecting hot and cold water lines with long-lasting braided stainless steel tubing, not brittle plastic. When applicable, we handle garbage disposal installation during the same visit.
Faucets come in many configurations — 1-hole, 3-hole, or deck-mounted — and we make sure your new faucet is installed and pressure tested thoroughly. Moving a sink to a new spot involves rerouting drains and vents plus extending supply lines; that’s a bigger job with permits, but we’re pros at handling it.
Dishwasher & Appliance Plumbing
We connect dishwashers by linking hot water supply and routing the drain line properly with a high loop or air gap to prevent backflow. Although electrical work is done by electricians, we coordinate to ensure everything meets requirements. For refrigerators with ice makers or water dispensers, we run dedicated cold water lines with accessible shutoff valves, using copper or braided stainless tubing supported correctly.
Additional appliance plumbing includes instant hot water dispensers and under-sink water filtration or reverse osmosis systems. For RO units, we install dedicated faucets and handle supply and drain hookups, plus explain maintenance for filter changes. Call us at 708-734-6594 for any appliance plumbing needs.
Gas Line Installation for Kitchen Appliances
Switching from electric to gas? Adding a gas cooktop to an island? We run new gas lines sized for your appliance’s BTU requirements. We route the gas piping from your meter or existing line, install shutoff valves, use code-compliant flexible connectors, and pressure test every connection. We also handle permits and inspections so that everything is safe and legal. Visit our gas line services page for a detailed breakdown.
Note: gas line rough-in must happen before cabinets go in. Trying to retrofit gas lines after cabinetry is installed is tricky and costly. Plan ahead with your general contractor and us to avoid delays.
Pot Filler Faucet Installation
Pot fillers are convenient wall-mounted faucets above the stove for filling pots without hauling water across your kitchen. Installing one requires running a cold water line inside the wall at about 56 to 60 inches from the floor and positioned near the cooktop. This is simple during a remodel when walls are open, but in finished kitchens, it means cutting into the wall and patching afterward. Reach out at 708-734-6594 so we can discuss your options.
Island Sink Drain & Vent Solutions
Installing a sink in a kitchen island means extra effort since island drains can’t vent through the wall like typical sinks. We use code-approved methods like island loop vents or air admittance valves (AAVs) depending on local rules. Running hot and cold water supply to the island is straightforward, but the drain and vent parts involve running pipes through the floor and subfloor. We’ve installed plenty of island sinks and can help plan your setup to avoid surprises.
Kitchen Plumbing Checklist
- Removal and installation of sinks: undermount, farmhouse, drop-in
- Installing faucets of any style or mounting type
- Garbage disposal installation or replacement
- Connecting dishwasher water supply and drain
- Running water lines for refrigerator ice makers
- Gas line installation for stove, cooktop, or oven
- Pot filler faucet rough-in and setup
- Installing or upgrading under-sink water filtration or RO systems
- Planning island sink drain and venting
- Replacing shutoff valves around the kitchen
- Adding prep or bar sinks in pantries or islands
Timing Tips for Kitchen Plumbing
- Confirm sink placement before demolition: Moving sinks is the priciest plumbing change, so nail down location before cabinet ordering.
- Schedule gas line work before cabinetry: Running new gas lines to islands or new stove spots must happen early.
- Install pot fillers before backsplash: Easier to open walls before tile is installed.
- Upgrade shutoff valves while accessible: Replace old gate valves with ball valves during plumbing exposure for reliability.
- Run fridge water lines before countertops: It’s simpler to install ice maker lines before counters are set.
Common Kitchen Plumbing Questions
Yes, though it’s one of the more complicated plumbing moves because island sinks require special venting like an island loop or air admittance valve. Supplying water is straightforward, but underfloor drain and vent routing need planning. We’ve handled many island sinks and can guide you. Call us at 708-734-6594 before you lock in your island layout.
For simple replacements like swapping faucets or disposals in the same spot, permits usually aren’t required. But any work rerouting drains, installing new supply lines, running gas lines, or changing the plumbing layout does require permits. We take care of all permitting and inspection coordination as part of our service.
Definitely. Installing gas lines during a remodel when walls are open is the best time. We size, run, and pressure test your gas line for ranges, ovens, and cooktops, plus handle all permitting. Make sure to book this before cabinets go in to avoid costly rework.
Yes, we often subcontract plumbing on kitchen remodels and coordinate closely with general contractors and designers to keep the project on track. We handle scheduling, permits, and inspections. Give us a call at 708-734-6594 to get us involved early.